Get 12% OFF Automatically When You Spend $2,000 or More No Code Required
Get 12% OFF Automatically When You Spend $2,000 or More No Code Required

FREE SHIPPING ON ORDERS OVER $1K

EXPERT LIGHTING ADVICE

VALUE ENGINEERED QUOTES

ROI ANALYSIS AND DESIGN SUPPORT

GFCI Outlets

Products List

Sort By:

Display Type:
Filters
  • Product
  • Qty in Cart
  • Quantity
  • Price
  • Subtotal
  • Total: items /

Adding your products to cart

View Cart Continue Shopping

Most GFCI purchases start with a code question, not a product question: where exactly is a GFCI outlet required, and when does a GFCI breaker make more sense? The chart below answers the first, the comparison answers the second, and the grade guidance covers what to actually put on the order.

Where the NEC Requires a GFCI Outlet

The requirements live in NEC 210.8, and the 2023 edition expanded them again. This chart summarizes the common locations; it reflects the 2023 NEC, and adoption varies by state, so verify the edition and any amendments in force in your jurisdiction.

LocationDwellings, 210.8(A)Commercial and Other, 210.8(B)
BathroomsRequiredRequired
KitchensRequired; the 2023 edition covers all dwelling kitchen receptacles, not just countertopRequired, including commercial kitchens
OutdoorsRequiredRequired
GaragesRequiredRequired, including service bays and similar areas
BasementsRequired; 2023 covers finished and unfinished areasCovered where the damp or wet location rules apply
Laundry areasRequiredRequired
Within 6 ft of sinks, tubs, or showersRequiredRequired
RooftopsFalls under the outdoor requirementRequired
Indoor damp and wet locationsCovered by the location rules aboveRequired

GFCI Outlet or GFCI Breaker

FactorGFCI OutletGFCI Breaker
Protection pointThe receptacle, plus anything wired through its load terminalsThe entire branch circuit, wiring included
Reset locationAt the outlet, in the room where it trippedAt the panel
Best fitRetrofits, kitchens and baths where local reset mattersNew circuits, dedicated equipment, spots with no accessible receptacle
Cost patternLower per protected point when one device feeds several downstreamEconomical when the whole circuit needs protection anyway

For most remodel and tenant improvement work, the receptacle wins: resets happen where people are, and one device wired feed-through protects every standard receptacle downstream on the run. Breakers win for dedicated equipment circuits, dishwasher and disposal locations with no accessible receptacle, and new construction where whole-circuit protection simplifies the layout.

Grades and Features Worth Specifying

GFCI receptacles come in 15A and 20A ratings and install in a standard device opening. Current UL 943 listings include self-test circuitry that automatically verifies trip function and flags end of life, so self-test is the default on new product rather than an upgrade. Weather-resistant (WR) models are required in damp and wet locations, paired with in-use covers per NEC 406.9; find enclosures under weatherproof boxes and in-use covers. Tamper-resistant versions satisfy NEC 406.12 where it applies, and commercial-grade devices bring higher cycle ratings for daily-use environments. One naming note: the trades write GFI outlet, the code says GFCI receptacle, and both mean the device on this page.

Rounding Out the Order

Standard duplex devices for the rest of the circuit live under receptacles, the full wiring device range starts at outlets, and matching finishes come from wall plates. Smart monitoring and USB combination devices are under smart wiring devices. Outfitting a multifamily building or commercial kitchen? Send the device counts and we will quote GFCI outlet packages by grade and finish at contractor pricing.

Frequently Asked Questions

Use a GFCI outlet when resets need to happen in the room and when one feed-through device can protect several downstream receptacles, which covers most kitchen, bath, and retrofit work. Use a GFCI breaker for dedicated equipment circuits, locations with no accessible receptacle, and new circuits where protecting the entire run, wiring included, is the cleaner design.

Line terminals connect to the incoming power from the panel; load terminals feed downstream receptacles so they share the GFCI protection. Reversing them is the classic GFCI outlet installation error: the outlet may power up but will not protect, and self-test models will flag the fault. If you are not extending protection downstream, land power on line and leave load unused.

The device is detecting current leaking to ground. Common causes: moisture in the box or downstream receptacles, a damaged cord or appliance on the circuit, too much cumulative leakage from long downstream runs, or an aging device. Unplug everything and reset; if it holds, reconnect loads one at a time to find the offender. A GFCI that trips with nothing connected has likely reached end of life.

Yes, when wired feed-through: standard receptacles connected to the GFCI's load terminals receive the same ground fault protection. This is how a single device at the first position on a circuit protects an entire kitchen or garage run. Downstream receptacles protected this way must carry the GFCI Protected label from the sticker sheet included with the device.

A device tested for the corrosion, moisture, and temperature exposure of damp and wet locations, marked WR on the face. The NEC requires WR-rated receptacles outdoors and in similar environments, and wet-location installs also need an extra-duty in-use cover per NEC 406.9 so the enclosure stays sealed while a cord is connected. Order the WR GFCI and the cover together.

The device runs an automatic internal check of its trip circuitry on a regular cycle and signals end of life, typically with an indicator light or by refusing to reset, when the protection can no longer function. UL 943 brought self-test into the standard, so current production devices include it. Monthly manual test-button checks remain good practice on older installed devices.

Yes. The NEC permits 15A receptacles on a 20A branch circuit when the circuit serves more than one receptacle, and a single duplex counts as two. The 15A device passes 20A feed-through, so downstream protection is unaffected. Use a 20A (T-slot) GFCI where a single receptacle serves the circuit or where equipment with a 20A plug will connect.

Yes, and it is the code-recognized upgrade path where no ground wire exists. The GFCI provides shock protection without a grounding conductor, and the installation must carry the No Equipment Ground label from the included sticker sheet. Downstream receptacles fed through it get the same protection with the same labeling requirement. Note that GFCI protection does not create a ground for surge strips or equipment that needs one.