Get 12% OFF Automatically When You Spend $2,000 or More No Code Required
Get 12% OFF Automatically When You Spend $2,000 or More No Code Required

FREE SHIPPING ON ORDERS OVER $1K

EXPERT LIGHTING ADVICE

VALUE ENGINEERED QUOTES

ROI ANALYSIS AND DESIGN SUPPORT

Outdoor Flood Lights

Products List

Sort By:

Display Type:
Filters
  • Product
  • Qty in Cart
  • Quantity
  • Price
  • Subtotal
  • Total: items /

Adding your products to cart

View Cart Continue Shopping

Outdoor Flood Lights Selected by Target, Not by Wattage

Most flood light listings ask you to pick a wattage and hope. That works until the fixture is 30 feet up a pole and the pavement below it is still dim. The faster path is to start from what you are lighting: the mounting height, the throw distance to the target, and the footcandle level the application needs. The tables below cover that selection math, then the mounting hardware that puts the beam where you aimed it.

Lumen Output by Mounting Height

Use mounting height as the first filter. These ranges assume a single fixture covering a typical target area; large areas at wide spacing need more fixtures, not just more lumens per fixture.

Mounting HeightLumen RangeTypical Applications
8 to 12 ft3,000 to 7,000 lmEntries, walkways, small signs, accent on low facades
12 to 20 ft7,000 to 15,000 lmBuilding facades, loading areas, small lots
20 to 30 ft15,000 to 30,000 lmParking areas, storage yards, perimeter security
30 to 40 ft30,000 to 60,000 lmLarge lots, truck courts, multi-fixture pole tops
Over 40 ft60,000 lm and upHigh mast and sports applications; see the high mast category

Beam Angle by Throw Distance

A flood light aimed at a distant target wastes most of a wide beam. Match the beam spread to how far the light has to travel and how large the target is.

Beam AngleThrowBest For
Narrow spot, 15 to 30 degreesLong throw, 50 ft and beyondFlag poles, steeples, signage lit from ground level
Medium, 30 to 60 degreesMid throw, 20 to 50 ftFacade sections, trees, monument features
Wide flood, 60 to 120 degreesShort throw, area coverageParking, yards, security zones, general area light

For parking and security work, plan around IES-style targets of roughly 1 to 5 footcandles maintained on the pavement, with the higher end for active vehicle areas and the lower end for perimeter zones. Facade and sign work is judged by uniformity across the surface rather than a single footcandle number, which is where beam choice matters most.

Knuckle, Yoke, or Slipfitter: Matching the Mount to the Install

The same LED flood lights often ship with a choice of bracket, and the wrong one adds a field trip. Knuckle mounts thread onto a junction box or ground stake and pivot for aiming, which suits ground-mounted facade and landscape-scale floods. Yoke and trunnion mounts bolt flat to a wall, canopy, or pole cross-arm and lock the aim with a fixed bracket, the standard choice for wall and surface installs. Slipfitter mounts slide over a 2-3/8 inch pole tenon, making them the default for pole-top area and yard lighting. Dedicated hardware for cross-arms, tenon adapters, and wall brackets is in Flood Light Mounting Brackets.

LED Flood Lights by Application

Facade and architectural work favors medium beams, 3000K to 4000K color, and fixtures placed to grade the light evenly up the surface. Signage is a linear problem: for wide sign faces, purpose-built fixtures in Sign Lights and Linear Flood Lights give better uniformity than a single point-source flood. Parking and area coverage at pole height overlaps with Area Lights and Shoebox Fixtures, which trade the aimable bracket for engineered distribution patterns. For fields and very tall poles, step up to Sports Lighters and High Mast Lights.

Contractors replacing HID floods should verify circuit capacity before a one-for-one swap; an LED unit delivering equal light typically draws 40 to 60 percent of the HID wattage, but inrush characteristics differ from ballast-driven loads. IP65 or IP66 wet-location ratings and 120-277V drivers are standard across most commercial-grade units, with 0-10V dimming on spec-grade models.

Flood Lights with Photocells and Motion Sensors

Dusk-to-dawn photocells suit perimeter and yard fixtures that should run all night. A floodlight with a movement sensor fits security zones where light on demand is the point: the fixture holds at off or a dim standby level, then drives to full output on detection. Many commercial units accept a twist-lock photocell receptacle, sensor, or shorting cap on the same fixture, so the control choice can be made per location rather than per model. Standalone controls are in Photocell Controls, and dedicated motion-activated fixtures are in Motion Sensor Lights.

Frequently Asked Questions

Start from mounting height. Fixtures at 8 to 12 feet typically need 3,000 to 7,000 lumens, 12 to 20 feet calls for 7,000 to 15,000, and pole mounts at 20 to 30 feet run 15,000 to 30,000 lumens. Above 30 feet, plan on 30,000 lumens and up, often across multiple fixtures. Large areas are solved with fixture spacing, not just brighter fixtures.

Match the beam to the throw distance. Narrow spots of 15 to 30 degrees reach distant targets like flags and ground-lit signs. Medium beams of 30 to 60 degrees suit facades and features at 20 to 50 feet. Wide floods of 60 to 120 degrees cover parking, yards, and security zones close to the fixture. A wide beam aimed at a far target wastes most of its output.

A knuckle mount threads onto a junction box or ground stake and pivots for aiming, common on ground-mounted floods. A yoke or trunnion mount bolts to a wall, canopy, or cross-arm with a fixed locking bracket. A slipfitter slides over a standard 2-3/8 inch pole tenon for pole-top installs. Many fixtures are offered in all three versions, so confirm the bracket before ordering.

Yes. A common security configuration uses a photocell to enable the fixture only after dark and a motion sensor to bring it from off or a dim standby level to full output on detection. Many commercial flood lights include a twist-lock receptacle that accepts a photocell, sensor, or shorting cap, so the control scheme can be set per location on the same fixture model.

Plan on roughly 150 to 200 watts of LED to replace a 400 watt metal halide flood, delivering equal or better illuminance at 40 to 60 percent of the connected load. Compare delivered lumens and beam pattern rather than wattage alone, since LED optics put more of the output on the target. Verify circuit capacity when swapping multiple fixtures on one branch.

Commercial-grade LED flood lights are typically rated IP65 or IP66 and listed for wet locations, which covers direct rain exposure on walls, poles, and ground mounts. Confirm the rating on the spec sheet for the specific model, along with the operating temperature range for your climate. Coastal and corrosive environments may also warrant a finish or housing rated for salt exposure.

Most commercial units ship with universal 120-277V drivers, and many larger fixtures offer 347-480V options for site lighting circuits. Spec-grade models commonly include 0-10V dimming leads, which allows integration with lighting controls or a dim standby level paired with a motion sensor. Check the spec sheet for the dimming protocol and low-end dimming level before pairing with a control system.